Viberation !

RSS
Email

0 Kudo

Author	Comment
circletracktom	Viberation !	Lead	[-]
Posts: 193 (05/18/08 02:49 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	Tags : None I have a 06 gsxr in an LC4 with a winters floter and can not find the vibration ! Not drive shaft or u joints 1 Had a bent output shaft on motor and bent drive shaft last year and had it replaced the vibration come back last week end . I had the new drive shaft out and checked for balence and straight , The car went up in the air and come down on the left rear wheel and bent the control arm and drive shaft and output shaft last year ! The rear end is not bent and axels are straight ! Sure hope some one can help ! Thanks ! Tom Last Edited By: circletracktom 05/18/08 02:51 PM. Edited 1 time.
247rocket		#1	[-]
Posts: 275 (05/18/08 03:33 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	you checked all wheels and jacked car up and dry run sitting in shop . if you have a winters pull axle shaft on left and dry run sitting in shop . then left ,
247rocket		#2	[-]
Posts: 276 (05/18/08 03:34 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	left then right sorry
fastonstreettires		#3	[-]
Posts: 17 (05/18/08 10:18 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	tom don't forget to check the input shaft and pinion shaft on your Q-change and the bearings that the shafts run on also who won at north platte Andy Rogers
circletracktom	Done that Andy !	#4	[-]
Posts: 194 (05/18/08 10:46 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	Hi Andy ! Was going to come down and say hi but knew things were not good there ! The 54 car won at North Platt ! Send me a Email twebb24720@aol.com ! Latter Tom .
circletracktom		#5	[-]
Posts: 195 (05/18/08 10:51 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	No vibration with out beeing driven , Nothing on stands ! It is a full floater and will pull axels and run in lathe again as I done it last winter and nothing and have not hit anything this year yet ! Thanks Tom
fastonstreettires		#6	[-]
Posts: 18 (05/19/08 01:41 AM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	are your jack stands under the frame or the rear diff if there under the frame then there is no load on the diff and this could be hiding the problem just thought of that check your output shaft on the tranny some thing deeper maybe bending the shaft or maybe a bearing was installed on the shaft wrong and it has failed
starters96	north platte	#7	[-]
Posts: 586 (05/19/08 08:40 AM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	Hey Tom: How many cars were at North Platte? thanx, Vaughn at starterman96@aol.com
karter25		#8	[-]
Posts: 310 (05/19/08 09:50 AM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	Make sure the bearings are nice and tight as well. We had a loose RR bearing last year and it caused a nasty vibration that would shake your teeth out. Bud Watson, #15 Modlite If we draw it, they will come. Cutting Edge Vinyl Signs www.cevsigns.com
jbark51	i second the hub bearing	#9	[-]
Posts: 924 (05/20/08 04:00 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	I had a similar issue with hub bearings being slightly overtight. It only vibrated under load. Could not duplicate in the shop. JB
247rocket		#10	[-]
Posts: 277 (05/20/08 05:54 PM) Reply Quote More My Recent Posts Message Me Connection Blocking Invite Ignore User's Posts	tom can you dial rear brake in and run with wheels only try to brake and accelerate and make the vibration show up . have somebody watch it close and look 4 it , jackstands under rear tubes so axle can wrap .

<< Previous Topic Next Topic >>

Yuku free message boards

Viberation !

Viberation !

Quick Reply